resistor color code

Resistor Color Code: How to Read Resistor Bands (Chart Included)

A resistor is one of the smallest components on a circuit board, too small to print its value on. Instead, manufacturers paint colored bands around its body, and those bands spell out the resistance in ohms. Learn the code once, and you can read any resistor in seconds.

This guide explains the resistor color code chart, how to read 4-band and 5-band resistors step by step, and the common mistakes that trip beginners up. You will also see worked examples and how to check your reading with a multimeter.

Why Resistors Have Color Bands

Resistors are too small for printed numbers, and the numbers would be hard to read at an angle anyway. The color code solves the problem: a set of colored bands, read from one end to the other, gives the value and the tolerance. The code is an international standard (IEC 60062), so a resistor bought anywhere in the world reads the same way.

Each color stands for a digit from 0 to 9. Black is 0, brown is 1, red is 2, orange is 3, yellow is 4, green is 5, blue is 6, violet is 7, gray is 8, and white is 9. A handy mnemonic is “Black Boys Race Our Young Girls But Violet Generally Wins.” Either way, the order is the same.

The code works because resistance is the one property every resistor is sold by. The bands are that property, printed in color.

The Resistor Color Code Chart

ColorDigitMultiplierTolerance
Black0x1–
Brown1x10+/-1%
Red2x100+/-2%
Orange3x1,000–
Yellow4x10,000+/-5%
Green5x100,000+/-0.5%
Blue6x1,000,000+/-0.25%
Violet7x10,000,000+/-0.1%
Gray8x100,000,000+/-0.05%
White9x1,000,000,000–
Gold–x0.1+/-5%
Silver–x0.01+/-10%

The first two or three bands are digits, the next band is the multiplier (how many zeros to add), and the last band is the tolerance, that is, how far the real value may sit from the printed one. Gold and silver appear only as multiplier or tolerance bands, never as digits.

Electrical symbols and diagrams including the resistor symbol and color bands
Figure 1: Resistor symbols and color band positions in a circuit diagram.

How to Read a 4-Band Resistor

A 4-band resistor has two digit bands, one multiplier band, and one tolerance band. Hold the resistor so the tolerance band (usually gold or silver, and set apart from the others) is on the right. Then read the bands from left to right.

Example: yellow, violet, red, gold. Yellow is 4, violet is 7, red is a multiplier of x100, and gold means +/-5%. The value is 47 x 100 = 4,700 ohms, or 4.7 k ohms, +/-5%. So the real resistance lies between 4,465 and 4,935 ohms.

How to Read a 5-Band Resistor

A 5-band resistor adds a third digit band, which gives one more significant figure. The layout is three digits, a multiplier, and a tolerance. The extra digit matters for precision resistors, where the tolerance is 1% or better.

Example: brown, black, black, red, brown. Brown is 1, black is 0, black is 0, red is a multiplier of x100, and brown means +/-1%. The value is 100 x 100 = 10,000 ohms, or 10 k ohms, +/-1%. The same resistor as a 4-band type would read brown, black, orange, gold, that is 10 k ohms, +/-5%, but the 5-band version is five times more precise.

The value you get from the bands feeds straight into Ohm’s law when you work out the current or voltage in your circuit.

Worked Examples

A few more readings to practice on:

  • Red, red, brown, gold = 22 x 10 = 220 ohms, +/-5%
  • Orange, orange, black, gold = 33 x 1 = 33 ohms, +/-5%
  • Green, blue, yellow, gold = 56 x 10,000 = 560 k ohms, +/-5%
  • Brown, green, black, black, brown = 150 x 1 = 150 ohms, +/-1% (5-band)
  • Yellow, violet, black, gold = 47 x 1 = 47 ohms, +/-5%
Digital multimeter measuring the resistance of a resistor
Figure 2: A multimeter on the resistance range confirms the value read from the bands.

Common Mistakes When Reading Resistor Bands

Beginners make the same few errors. The most common is reading the bands backward, starting from the tolerance end. Always put the gold or silver band on the right, or look for the band that sits slightly apart from the rest. Another is confusing red with brown and orange with red under warm light; check the colors in daylight or under a white LED.

A third mistake is forgetting the multiplier: brown, black, red is 1,000 ohms, not 12 ohms. And a fourth is ignoring the tolerance when the value matters. A 5% resistor is fine for an LED current limiter but not for a precision voltage divider. For a reminder of how resistors behave alongside capacitors and inductors, see our guide to the difference between resistance and reactance.

Checking a Resistor with a Multimeter

When in doubt, measure. Set a digital multimeter to the resistance range, touch the probes to the resistor’s leads, and read the value. It should fall inside the tolerance band of the coded value. If it reads open-circuit, the resistor is broken; if it reads far outside tolerance, it may have been damaged by heat.

What is resistance — resistor symbol and circuit diagram
Figure 3: The resistor color code turns a few bands of paint into an exact resistance value.

Frequently Asked Questions

Which end do I start reading a resistor from?

Start from the end opposite the tolerance band. The tolerance band is usually gold or silver and sits slightly apart from the other bands. If there is no gold or silver band, look for the band closest to one end. The first digit band sits nearer the end than the tolerance band does.

What does a gold band mean on a resistor?

It depends on its position. As the last band it means a tolerance of +/-5%. As the multiplier band (third or fourth position) it means multiply by 0.1. A resistor with a gold multiplier band is always under 10 ohms.

How do I read a 3-band resistor?

A 3-band resistor has two digits and a multiplier, and no tolerance band. Its tolerance is +/-20%. Read it the same way as a 4-band resistor, but skip the tolerance step.

What causes a resistor to read the wrong value?

Heat, age, and faded paint can make bands hard to read, and a resistor that has overheated may have drifted from its marked value. When the value matters, in a divider, a timing circuit, or a current sense, measure with a multimeter and confirm.

Why are some resistors blue instead of beige?

The body color tells you the resistor family. Beige or tan bodies are usually carbon film, while blue bodies are usually metal film. Metal film resistors are more precise and more stable, and they often have five bands instead of four.

Conclusion

The resistor color code is a compact language: two or three digits, a multiplier, and a tolerance, all painted on a component smaller than a grain of rice. Learn the color order, read from the end opposite the gold or silver band, and check the result with a multimeter when it matters, and you will never need to guess a resistor’s value again.

For more worked examples and a printable chart, the Electronics Tutorials guide to resistor color codes is a useful next read.

Comments

No comments yet. Why don’t you start the discussion?

Leave a Reply

Your email address will not be published. Required fields are marked *